How to Fix a Dripping Shower Head or faucet is one of the nightmares of the homeowners.
It is an irritating and annoying situation that someone must face once in a life.
A leaky showerhead waste hundreds of gallons of water. Top of that, dripping hot water side of the showerhead not just wastewater but also waste significant energy.
As you know, the heater consistently operates to warm the water. It is the worst situation that costs you double.
If you are here, to find a solution, then congratulations, you are in the right place. Here, you will get simple solutions.
After reading this article, you will never contact a plumber for this kind of situation.
You will able to handle this situation on your own. Let’s get started and learn how to fix a dripping shower head with these helpful and straightforward Methods.
Let’s get started and learn how to fix a dripping shower head with these helpful and straightforward Methods.
Also Read: How to Change a Shower Head?
Methods of Fixing the Leak Showerhead:
It is essential to learn how to fix the leakage issues in the home because these issues are frustrating and costly.
The reasons behind the dripping shower head are not just one.
Therefore, the solution is also not one.
In this section, few methods would be discussed by which you can figure out the problem and quickly fix a leak shower head cost-effectively.
Unclogging Showerhead Holes:
First of all, turn the shower off at the valve and inspect the showerhead. One reason behind a leaking showerhead can be caused by clogged because minerals deposits build up in the holes over time.
If you are not sure what the cause of the leak is, then it is a cost-effective and straightforward method.
- Shut off the water supply: It is essential to shut off the water completely. You can turn off the water in two ways. Shutoff the valve of the showerhead or turn off the main water supply. According to me, turn off the water supply directly to the bathroom easier than shutting off the main supply of the home. The valve of the bathroom usually be near the shower, turn off it.
- Remove the entire showerhead: To unclog the showerhead, you will have to remove the showerhead from the shower arm. Unscrew the faceplate or unscrew showerhead as the whole. Undo the screws that are around the showerhead faceplate or the showerhead. Then counterclockwise twist it, and remove.
- Dip the showerhead in white vinegar: Take a large container that effortlessly holds the showerhead. Fill your tank with white vinegar with some coarse salt. This mix solution should be in enough amount in the tank that quickly covers showerhead or faceplate. For 8 hours, do not eject the showerhead or faceplate from the container. After the time is up, vinegar will dissolve the minerals deposits.
- Manually remove remaining minerals deposits: If you still see the minerals deposits, then manually eliminate them with the help of a toothpick or small wire that perfectly fit in the holes. Insert the toothpick into each hole of the showerhead faceplate and remove the debris. And then scrub the faceplate with a plastic brush. You can also use the air compressor to blow out the waste.
- Inspect if the leaking shower head is fixed: Now, attach the faceplate or showerhead back into their place, and determine by unclogging the holes, the leaking issue has fixed or not. Turn on the water supply to the showerhead. To check the leak, turn off the faucet. For a while, examining a water leak, if showerhead does no leak, then congratulate yourself, you have solved showerhead leak issue.
Replacing a Worn Rubber Washer:
If your showerhead leaks again after unclogging the showerhead, then there must be another reason for the leak.
Over time, rubber washer starts to crack, and water leaks from the showerhead.
By replacing a worn rubber washer, you can prevent the showerhead leak.
- Completely turn off water supply: First of all, shut off the water supply to the bathroom. Experts said by applying lubricant, a washer can be maintained. Keep in mind one thing, if your shower faucet is compression faucet, then you need to determine the which valve is leaked. Is it from a cold-water valve or the hot-valve water?
- Determine which washer needs to replace: It is essential to know which type of faucet you have; it will help you determine which rubber washer needs to replaced. In case, you have compression faucet, that means two-handle valve, then you will replace the rubber washer that’s inside the faucet. On the other hand, if you have single handle faucet, then you will replace the rubber washer that’s inside the showerhead.
- Replace the rubber washer in the showerhead: To replace the rubber washer inside the showerhead, you need to take off the showerhead from the shower arm. Protect the fixture and loosen the collar nut that attaches to the shower arm. Once you remove the showerhead, look under the showerhead’s swivel ball, find the rubber washer, pull it off, and then replace it with a new rubber washer of similar size, style, and thickness. Make sure that the new rubber washer works appropriately.
- Replace the rubber washer in the faucet: Remove the faucet handle appropriately. The temperature of the leaking water helps you to determine which faucet handle need a new rubber washer. The screw of the faucet may be hidden behind a cover cap. In case, you have old model faucet then screw may be either on the front or side of the faucet. Once you remove the screw, pull the handle harder to pull it off the faucet body with the help of faucet puller. When the handle is off, remove the trim and sleeve from the faucet stem. After that, unscrew the faucet stem that held down by a hex nut. By using deep socket unscrew the hex nut that has six sides. You know what? A socket wrench specially used for this purpose. Now, after this whole process, you can replace the rubber washer with a new one.
- Reassemble the shower parts and check problem’s fixed: After replacing the rubber washer in the showerhead, the reassemble the showerhead onto the shower arm. And turn on the water supply to ensure the leak has been fixed or not. It is advisable, do not over tighten the showerhead before confirming the problem is solved or not.
In case, you change the rubber washer in the shower faucet, then reassemble the shower faucet, and starting with the faucet stem. Apply little bit grease on the threads, and screw the stem back on its original position. Finally, put the handle back in place. Keep in mind, do not screw the handle on its location, until you confirm the leaking showerhead is fixed. Turn on the water supply for confirmation.